Inwales fitted and fastened

The new inwales were cut from some close-grained Douglas Fir and had some gentle tapering to fit snugly behind the existing breasthook and quarter knees that had been left in place. A beading was planed on the lower edge of the timber as had been done on the stringer below it. The inside face of the timber was given a couple of coats of wood stain/preserver and then clamped firmly in place and fastened all round starting at the stem and working aft. Once fastened through all the timber heads the  Jack Nichols was glued in place each side of the stem and the long copper nails through the breasthook, thwart knees and quarters were driven and fastened.

Inwales being planed down to sheer level.

Quarter knee re-fastened clamping inwale.

Fitting thwarts and preparing the inwale

After fitting and fastening new stringers the mid ships and forward thwarts were re-fitted and a new after thwart made from hardwood and given a beaded edge to match the other two. The thwart knees are basic bent angle brackets but neatly made and were galvanised.  Ideally they should have been re-dipped but I gave them a good clean up and a few coats of 'galvafroid'. These were bolted back in after priming the timber edges using the original screws which are stainless M8 countersink - a clue that this little boat is not as old as she looks.
I intend to fit an inwale to the insides of the full-height timbers and this is a change to her original construction. In preparation for this I am fitting sections of timber between the ribs in way of the thwarts, the rowlock positions and at the vessel's ends.

Thwart refitted and fastened - This is mid ships port side.

Short sections of timber glued between ribs to make a solid inwale. Here is port side mid ships rowlock position.

Fitting stringers and thwarts

Now that all the new ribs/timbers are fitted and fastened I turned my attention to fitting new stringers (sometimes called 'risers') at thwart level. The existing thwarts were bolted back into place with their galvanised iron knees and the new stringers sprung and wedged into place and then fastened trying to pick up existing fastening holes where possible. The after thwart was a non-original and over thick piece of softwood and some new Iroko is on order to make a new one to match the two other hardwood items.

Existing thwarts re-fitted and new stringers fastened in.

New stringers replaced originals that were in various short sections.

A Redwing undergoing a re-fit

A Redwing sailing friend has been busy locally doing a major refit on a 1952 Dann-built Redwing, 'Pegasus' that had been laid up in his barn for many, many years after he rescued her from deterioration outdoors after previous owners had lost interest. 'Pegasus' was in need of a new deck, new ribs, various other minor repairs and a few updates like the retrofitting of Centreplate case stiffeners and provision of transom ports.
Typical of old Redwings is the failure of glue joints in the deck beams, carlings and other deck/framing joints and here 'Pegasus' has been meticulously re-glued. Her owner is a professional bespoke wooden furniture maker and the quality of his workmanship is top-notch.  He was at the re-ribbing stage here and I have been lending a hand to fasten new frames.  Ash has been used here but being a bit dry before steaming necessitated a prolonged soaking in the pond before going into the steamer.

New ribs going in - doing this without the deck makes the job a whole lot easier!

She needs a complete strip and re-varnish job.

New main sheet horse and transom drains now cut.

Timber fastening progressing

We have now got all the new frames/ribs/timbers fastened in place apart from the timber heads which will be done when the new inwales are worked into the boat. When the new timber has had a chance to completely dry they will be give a soaking with wood preservative prior to painting to (hopefully) prolong their life this time.

New timbers fastened. The missing ones are where there are still other repairs required to the skin planking.

All new timbers in place

Finally I have steamed and bent in all the replacement timbers into Nanw. All the thwarts were removed and replaced with spalls to hold the sides together and, in the bow, to hold the sides apart as she wants to close in due to the pressure from the new planks and battens. The ribs in the bow were more difficult to fit than expected, due to quite a lot of twist needed to make them lie against the lands and they may have benefited from being 'hot-nailed' in place as soon as they were bent, to make them stay put.
I surprised myself by not breaking any of the new ribs in the process of fitting them. Therefore about 8 or so left over which I hope to use in another boat very soon before they dry out.
There is a bit of nailing up still to be done before the temporary G-clamps can be removed finally. A really worthwhile job was stripping, sanding and priming the inside of the hull as the old ribs were torn out. Once the job is all painted the boat will look like a new one - inside at least!

Priming the fore peak. She was closing in without the foreward thwart.

All new timbers finally fitted - just need fastening now.

More on timbering

We have been making steady progress with re-timbering Nanw. It was decided to take out 'batches' of timbers in sections and to date the mid ships and forward areas has been done and re-fastened to just below sheer strake level. We have just steamed another six in place aft of the after thwart so she is done to the transom. Progress is a bit faltering as I have to 'borrow' helpers to do the nailing.
The virgin timber is wrapped up in polythene and damp towels to prevent it drying out but it cannot stay like that forever, obviously, and the new wood is blackening with mould.
One job I have been able to do on my own to follow up the main nailing is to make and insert wedges between the timbers and the upper strakes to support them for when the inwale is eventually fastened through. Originally the timbers stopped short under the inwale timber which was fastened to the walestrake and knees only. I have decided to give her an open 'box' type gunwale with the timbers finishing flush with the sheer - a stronger and lighter arrangement.

Wedges fitted behind timbers. Black spots are from the clamps and will be hidden eventually.

After section of the boat cleaned out ready for timbering